mdanamulhasan.com Shop
Mechanical Design Data Handbook: Formulas, Checked Tables and Worked Examples

Mechanical Design Data Handbook: Formulas, Checked Tables and Worked Examples

A 69-page mechanical design data handbook: SI units, sections and beams, stress and fatigue, water, steam, air and R134a tables, pipe flow, ISO fits and tolerance grades, bolts, springs, gears, bearings, heat exchangers, pumps, fillet welds and process capability, with worked examples. PDF.

$5.99

The full handbook is the PDF: 69 pages on a 7 × 10 in page, typeset in LaTeX for print, with thirteen vector figures, worked examples and tables that you can check. This page is the overview, so you can see what is inside before you download it.

A data handbook is only useful if you can trust its numbers, so this one is built to be checked. Constants and conversion factors are exact by definition. Properties of water, steam, air and refrigerant R134a are computed with the open-source CoolProp library. Stress, section, spring, gear, bearing and heat-transfer values come from closed formulas printed beside each table. Standard dimensions (pipe, threads, property classes, tolerance grades) are published values of ISO, ASME and EN standards.

Mechanical Design Data Handbook cover with its five parts and a pipe friction formula

What the five parts cover

Part Topic
1 Fundamentals and mathematics: SI units, exact constants, conversion factors, geometry, statics and dynamics, section properties, preferred numbers
2 Materials and solids: standard grades with specified minimums, stress and beam formulas, deflection cases, buckling, springs, fatigue and the S-N line
3 Thermodynamics, heat transfer and fluids: water, steam, air and R134a tables, conduction, convection and radiation, friction factors and pipe pressure drop
4 Design and components: GD&T groups, ISO tolerance grades IT01 to IT18 and fits, metric threads and bolt torque, gears, power and torque, bearing life and vibration
5 Machine elements, heat exchange and quality: thick-walled cylinders, shafts and keys, heat exchangers (log mean and effectiveness), pumps and motors, thermal expansion, fillet welds and process capability
Appendices Pipe and tubing, beam sections, hardness conversion, temperature conversion, ISO tolerance data, a formula sheet and sources

The formulas you reach for most

Bending stress and the largest deflection of a beam follow from the section properties:

$$\sigma = \frac{M,c}{I} = \frac{M}{Z} \qquad\qquad \delta_{\text{cantilever}} = \frac{P,L^{3}}{3,E,I}$$

The thread stress area, which sizes a bolt, and the rating life of a bearing:

$$A_s = \frac{\pi}{4},(d - 0.9382,p)^{2} \qquad\qquad L_{10} = \left(\frac{C}{P}\right)^{p}$$

A look inside

Units, sections and beams

The seven SI base units and the derived units used most in mechanical design

Units come first: every other table depends on them.

Four sections with their area, second moment and section modulus

Section properties: $I = b h^{3}/12$ for a rectangle and $I = \pi d^{4}/64$ for a solid circle.

A cantilever and a simply supported beam under a point load and a uniform load

Beam deflection cases, such as $\delta = 5 w L^{4} / (384 E I)$ for a simply supported beam under a uniform load.

Stress and fatigue

Engineering stress-strain curve of a ductile steel

Stress and strain: $\sigma = E,\varepsilon$ in the elastic range, then yield, ultimate strength and fracture.

S-N curve of a machined steel shaft computed from the Basquin line

The fatigue worked example: $S_f = a N^{b}$ with the endurance limit at $10^6$ cycles.

Fluids and heat

Density and dynamic viscosity of liquid water

Water at 1 atm, computed with CoolProp: density peaks near 4 °C and viscosity falls to a sixth between 0 and 100 °C.

Temperature entropy diagram of water with three isobars

The T–s diagram of water with the isobars at 0.1, 1 and 10 MPa.

Darcy friction factor against Reynolds number for four relative roughness values

Pipe flow: the pressure drop is $\Delta p = f,\dfrac{L}{D},\dfrac{\rho v^2}{2}$, with $f$ from the Swamee-Jain equation.

A wall as three thermal resistances in series

Heat transfer: $\dot Q = \dfrac{T_{in} - T_{out}}{R_{in} + R_{wall} + R_{out}}$.

Fits and components

Standard tolerance against size for five ISO grades

ISO tolerance grades: each step in grade is about 1.6 times wider, and the zone grows with the size.

Rating life of ball and roller bearings against the load ratio

Bearing life: doubling $C/P$ multiplies the life of a ball bearing by eight.

Worked example: size a bolt preload and torque

The handbook is meant to be used, so here is one chain of table lookups worked end to end. An M12 × 1.75 class 8.8 bolt in a reusable joint:

An M12 class 8.8 bolt clamping two plates with stress area, proof load, preload and torque

Four lookups, four lines of arithmetic: stress area, proof load, preload and torque.

$$A_s = \frac{\pi}{4},(d - 0.9382,p)^2 = 84.3\ \text{mm}^2 \qquad F_p = S_p A_s = 580 \times 84.3 = 48.9\ \text{kN}$$

$$F_i = 0.75,F_p = 36.7\ \text{kN} \qquad T = K,F_i,d = 0.2 \times 36.7\ \text{kN} \times 12\ \text{mm} = 88\ \text{N·m}$$

The nut factor $K$ is the weak link: it depends on the thread, the surfaces and the lubricant, and the same torque can give very different preloads. This example assumes $K = 0.2$ and a preload of 75 % of the proof load. For a critical joint, find $K$ by test on the real parts.

Find the table you need

Seven common engineering questions mapped to the part of the handbook that answers them

Start from the question, not the contents page.

Conversions worth knowing by heart

Quantity Value
Standard gravity $g = 9.80665$ m/s² (exact), so 1 kgf = 9.80665 N
Pressure 1 bar = 100 kPa; 1 psi = 6.894757 kPa
Energy 1 kWh = 3.6 MJ
Power 1 mechanical horsepower = 745.7 W
Temperature $T_K = T_C + 273.15$

Pages from the PDF

Cover and contents page of the Mechanical Design Data Handbook

Pages of the handbook with the superheated steam tables

Pages of the handbook with the beam deflection cases

Pages of the handbook with the standard fastener tables

Pages of the handbook with the ISO tolerance grades IT01 to IT18

Pages of the handbook with the heat exchanger formulas and an example

How the numbers are made

Data Where it comes from
Constants and conversions SI definitions; exact factors
Water, steam, air and R134a CoolProp: IAPWS-95 for water and steam, the Lemmon model for air, the Tillner-Roth and Baehr equation for R134a
Sections, beams, springs, gears, bearings Closed formulas printed beside each table, worked in code
Thread areas and bolt loads $A_s = \frac{\pi}{4}(d - 0.9382,p)^2$ and ISO 898-1 property classes
Pipe and sections ASME B36.10M and EN 10365
Fits and tolerance grades ISO 286 tables, checked by script against the standard grades
Material strengths Specified minimums of the named standard grade

Always confirm a value with the data sheet or the standard before a design is frozen. This handbook is an independent reference: it does not reproduce any other handbook.

Choose your edition

The picker at the top of the page switches between three editions of the same material.

  • Cheat Sheet: a free five-page reference: conversions, sections, beams, stress, fits at 25 mm, bolts, gears and bearings, fluids and heat.
  • Handbook: this book, five parts and seven appendices, with worked examples and tables you can check.
  • Pro Handbook and Engineering Kit: the handbook plus a protected Excel workbook (bolted joints to VDI 2230, bearing life, beams, ISO 286 fits, springs), 27 printable flashcards and a guide.

[!NOTE] Rules of thumb in this handbook are starting values from common practice, not from a standard: confirm them with the data sheet or the standard before a design is frozen. Worked examples are illustrative unless they say otherwise.

Related

Independent work. Not affiliated with, sponsored by or endorsed by ISO, ASME, VDI or any standards body. Values are read from the standards named on this page or computed from their formulas, and are a reading aid only. The current edition of the standard governs.